ST Series Micro PCB Drill Bit for Aluminum and Plastics

The ST Series Micro PCB Drill Bit features a brazed carbide cutting section with two cutting lips and two flutes. Designed for aluminum alloys and plastics, its chip-space geometry accommodates continuous chips, while the dual-edge design helps reduce the risk of vibration and hole deviation during thin-sheet breakthrough.

Product Details

Small-hole drilling becomes more challenging when the workpiece is thin or the material produces long, difficult-to-break chips. Poor chip evacuation can disrupt cutting, while unstable tool engagement during breakthrough can affect hole roundness and dimensional accuracy.

The ST Series Micro PCB Drill Bit addresses these challenges with a brazed carbide cutting section and a two-lip, two-flute geometry. Its design is optimized for aluminum alloys and plastics, providing a practical drilling solution for applications where chip removal and consistent hole quality matter.

The ST series uses a dual-edge configuration rather than a single-lip design. This is particularly relevant when drilling thin workpieces, where the support acting on the drill can change abruptly as the cutting edge exits the material.

Why Does Drill Design Matter When Drilling Thin Sheets?

One challenge in thin-sheet drilling occurs at breakthrough. As the drill passes through the bottom surface, the workpiece can no longer support the cutting edge in the same way. Cutting forces change, and the drill may become more susceptible to vibration or deflection.

A single-lip drill can be more sensitive to this change because of its inherently unbalanced cutting arrangement. Under unsuitable conditions, this can contribute to out-of-round holes or deviations from the required diameter.

The ST Series uses two cutting lips to provide a more balanced cutting arrangement. This design helps address the breakthrough instability described above, making it relevant to thin aluminum components and other thin workpieces.

The two-lip design helps manage the risk of hole deviation; it does not guarantee accuracy on its own. Tool runout, workpiece support, drilling parameters, and the specific material also affect the finished hole.

Two Flutes for Chip Space in Aluminum and Plastics

Aluminum alloys can produce long, continuous chips that are difficult to break. Some plastic materials can also produce chips that require adequate space to leave the cutting zone.

If chips accumulate inside a small hole, they can interfere with stable drilling and affect the cutting process. This makes flute geometry an important selection factor for micro drills used with ductile materials.

The ST Series uses a two-flute design with a cross-sectional geometry optimized for the intended work materials. The available chip space is designed to accommodate chips that do not break easily, helping support more consistent chip evacuation.

For deeper holes or materials with particularly continuous chips, the actual drill dimensions and drilling conditions should be checked carefully. The product’s geometry is one part of the solution; chip evacuation also depends on hole depth, material grade, and cutting parameters.

Brazed Carbide Cutting Section for Practical Micro-Drilling

The ST Series features a carbide cutting section brazed onto the tool body. This construction provides a practical, economical approach to small-hole drilling in the specified work materials.

Its application focus is not simply making a small hole. The cutting geometry is intended to accommodate the chip formation associated with aluminum alloys and plastics while providing two cutting lips for a more balanced drilling arrangement.

When selecting a drill, match its available diameter and cutting length to the hole specification. Do not assume that every micro drill is interchangeable: hole depth, workpiece thickness, material behavior, and toolholding conditions can change the suitability of a particular configuration.

Recommended Workpiece Materials

The supplied product specifications identify two primary material groups:

  • Aluminum alloys: Suitable for small-hole drilling where chip evacuation and stability during breakthrough are important.
  • Plastics: Suitable for applications where the drill geometry is compatible with the specific plastic and hole requirements.

Different grades of aluminum and plastic produce different chips and respond differently to heat. Confirm the workpiece grade and required hole dimensions before determining cutting conditions.

Although the product is named a PCB drill, the supplied specifications establish aluminum alloys and plastics as its applications. They do not confirm compatibility with every PCB laminate, particularly abrasive glass-fiber materials such as FR-4. Confirm the actual board material before selecting the drill for that use.

How to Select the Right ST Micro Drill

Before ordering, check the following application details:

  • Hole diameter: Match the drill size to the required finished diameter and tolerance.
  • Workpiece material: Identify the aluminum alloy or plastic grade.
  • Sheet thickness and hole depth: These affect chip evacuation and the conditions encountered during breakthrough.
  • Hole quality: Specify the required diameter tolerance and roundness where these are critical.
  • Machine and toolholding: Check runout and setup stability, especially for small-diameter tools.

For thin-sheet applications, pay particular attention to the exit side of the hole. The two-lip design addresses one source of instability, but correct workpiece support and suitable cutting conditions remain necessary.

Technical Specifications

ParameterSpecification
Product SeriesST
Tool TypeMicro PCB Drill Bit
Cutting SectionBrazed carbide
Cutting LipsTwo
FlutesTwo
Primary Work MaterialsAluminum alloys and plastics
Design FocusChip accommodation and thin-sheet drilling stability

Specific drill diameters, flute lengths, overall lengths, point angles, and cutting parameters must be confirmed against the actual product specification. They are not included in the supplied description.

Frequently Asked Questions

Why choose a two-lip micro drill for thin aluminum sheets?

During breakthrough, the support acting on the drill changes as the cutting edge exits the workpiece. A two-lip design provides a more balanced cutting arrangement than a single-lip configuration, helping reduce the risk of vibration, deflection, and resulting hole deviations.

Is the ST Series suitable for plastic drilling?

Yes. Plastics are listed as an intended work material. The appropriate drill size and cutting conditions depend on the specific plastic grade, hole depth, and required hole quality.

Can this drill be used for FR-4 circuit boards?

The supplied specifications do not establish suitability for FR-4 or other glass-fiber laminates. Because these materials can be abrasive, confirm the intended PCB substrate and the manufacturer’s material compatibility information before selecting the drill.

Request a Quote for ST Series Micro PCB Drill Bits

To identify a suitable drill for your application, send JimmyTool your part drawing or hole specifications, including the workpiece material, required hole diameter, sheet thickness or drilling depth, and dimensional requirements.

These details help determine whether the ST Series geometry matches your application and which available drill size is appropriate.

Request A Quote

Tell Us What You Need